FPGA, CPLD, & System Management Optimized For Low Power & Small Size. FPGA board designed for SSD/NAND controller development. By default, it is equipped with Altera FPGA(StratixIII), NAND flash memory, DDR SDRAM, NOR flash memory and. Linux. CNC Documentation Wiki: Mesa Cards. Linux. CNC Supported FPGA- cards. Linux. CNC Supported Daughtercards. Products > Design Software & Intellectual Property; Design Software and IP Complete design flows, ease of use, higher productivity. LinuxCNC Supported FPGA-cards 3. LinuxCNC Supported Daughtercards 3.1. 50 pin Daughtercards (for all FPGA cards except 5I25) 3.2. Dear Friends, Here is second part of this tutorial series that is How to use hyper-terminal and serial communication with FPGA device using RS232 protocol. Microsemi SmartFusion2 SoC FPGA offer the industry's most secure, reliable and low power flash based FPGA with ARM Daughtercards (for all FPGA cards except 5. I2. 5)3. 2. 2. 5 pin daughtercards (for 5i. Smart Serial Daughtercards (connect via serial link)3. Daughtercard support in development. Daughterboard / Firmware Relation. Two drivers are supported by Linux. CNC. The older Hostmot- 4 firmware /driver is most mature, but only works with the 5i. The newer Host. Mot. Linux. CNC Supported FPGA- cards. Many of the MESA FPGA- cards use 5. I/O pins, 2. 4 GND- pins, and Power (GND+VCC). As an example cards with three of these connectors have 3x. I/O pins while the new 3x. I/O pins. 6. 8 pins, 1. RS4. 22/RS4. 85 1. MB. PCI interface. FPGA 2x DB2. 5 connectors, PCI interface. FPGA, 2 5. 0- pin connectors, 4. Parallel port interface. FPGA, 3 5. 0- pin connectors, 7. PC/1. 04- Plus interface. FPGA, 3 5. 0- pin connectors, 7. PC/1. 04- Plus interface. FPGA, 3 5. 0- pin connectors, 7. PC/1. 04- Plus interface. M, 1. 5. M, or 2. M FPGA, 6 5. 0- pin connectors, 1. PCI- E interface. Linux. CNC Supported Daughtercards. Daughtercards (for all FPGA cards except 5. I2. 5). 7i. 33 4 channel analog servo interface with encoder inputs. Isolated I/O card. Breakout/FPGA protection card. Quad 1. 00 Watt H- bridges for 4. I2. 7,4. I3. 4,4. I6. 5,5. I2. 0,7. I6. 0. 7i. 40 Dual 4. W driver. 7i. 29 Dual 2. KW H- bridge for 4. I2. 7 and FPGA cards. RS- 4. 22 interface. I/O protector. 7i. I/O + spindle control + 1 RS- 4. I/O + 1 RS- 4. 22 port. RS- 4. 22 interface. Smart Serial Daughtercards (connect via serial link). Note that all the Smart Serial cards require a RS- 4. Smart Serial card. Can connect up to 3. IO. 7i. 66 1. 6 input 8 output isolated Smart Serial remote I/O card. I/O TTL Smart Serial card. Smart Serial card. Smart Serial card. Control panel/pendant Smart Serial card. W 3- phase Smart Serial motor drive. Mainly for brushless motors. Daughtercard support in development. I6. 5 supported in . Generic SPI via custom components also now possible. Daughterboard / Firmware Relation. We'll use the 5i. Other boards are similar.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
January 2017
Categories |